Selasa, 24 Juni 2014

Clean pool?

Q. Okay, so I have this giant inground pool. I've had it for a few years (previous owners built it). Every time I open it, it is all green with algae. I know this will happen, but it takes me over 2 weeks to clean! It's only supposed to take a few days, one week at the most! I bought a new filter last year and it is still green. I always scrub it with an algae scrubber and vacuum the pool (p.s. what's the correct way to vacuum an inground pool?). I have the proper chemicals added too. What can I do to help clean it up faster?


Answer
I hope this isn't too long of an answer, but I hope it helps!

Adding the proper chemicals is what you should be doing, however you also need to make sure those chemicals are in proper balance with each other. Make sure your chlorine levels are where they should be and, more importantly, that they stay there.

Do you cover your pool in the winter? I don't cover mine; cleaning my pool is a year-round process. That means I'm not very familiar with cleaning techniques during winter if you do cover it, but I don't think that cleaning algae out of it is something you should have to do every year.

Sustaining circulation is also a good way to keep algae from clinging to the sides of your pool. Once they attach, they grow and spread quickly. Our pump runs for at least a few hours, every day...unless we go on a day trip out of town. I've also had my pump break down on me a few times where I had 0 circulation in my pool and within a week, my pool water went from a little cloudy to looking like green mud.

Are you familiar with backwashing? Diatomaceous earth (DE)? Sand? Backwashing is flushing your filter screens (in the pump) of small contaminants like dirt and algae particles. DE and sand is the filter aid you use that coats the screens of your filter to keep the stuff from getting re-deposited into your pool via the jets. Just look at the manufacturer's label on the pump and it should tell you what kind of filter you have; this should tell you what kind of filter aid it uses.

As for a "correct" way to vacuum, well there's really no right and wrong way to do it. There's automatic skimmer vacuums you can buy that get propulsion from your pump, and there's manual ones where you do it all yourself. The automatic ones will be pricier of course, but if you don't like breaking out in sweats or standing in bitter cold wind to operate a manual one, they can be life-savers.

Any questions you have can be directed to your local pool supply store; I prefer Leslie's myself, if you have one nearby--www.lesliespool.com. You can buy water test kits there; you dunk a test strip in the water and check where your chemical levels are so if any of them are off, they can be corrected. However, most places like this will also test a sample of the water you bring to their store and will offer advice.

How can I clean a pool that has algae?




ivan584


there's algae all over the sides of the pool and not much in the water


Answer
Hi Ivan, boy do I know this project! We had a beautiful 800 gallon, waterfall in our back yard, under a tree with sticky seeds that fell year-round. It's first name was green! So, I can tell you that pool supply companies, and some home or hardware stores carry algaecides that will do the job.

Preventative measures are the best. Use the pool sweeper to sweep down the sides of the pool daily. You can buy automatic sweepers, but you do need to check that they are doing the job -following them up at least weekly is best. If a lot of leaves get into the pool, remove them daily. If not so many get in the pool, every few days is good. But if the leaves build up, so will the algae. Make sure children, pets, and guests understand they must not go in the pool muddy or even a little dirty -that's what eats up your chlorine.

It's important to check the chlorine levels daily. This is the best thing you do to keep the pool safe and healthy. Don't skip this! Pool services abound, so you don't have to do all these things yourself. If you have a tree with small leaves near the pool, or where it's leaves get blown into the pool, remove it. If there are small gardens around the pool, exchange small-leaved shrubs for larger leaved shrubs, put down landscape fabric (NEVER black plastic) around the shrubs, and cover with a 4" layer of rock. Bark can be blown into the pool by wind.
I allow email through Yahoo! Answers if you have more questions. Just go to my profile page and click on the blue email line.




Powered by Yahoo! Answers

My swimming pool "Kreepy Krauly" automatic cleaner doesn't work well...?




jagercrow


Just bought a house with a pool. Got everything under control except for the "Kreepy Krauly" in the pool. I can get it to work, however, 1.) It sometimes won't stay suctioned flat on the pool surface. The back end will start to lift up. Is that normal? 2.) It will usually work for 5-10 minutes and then just stop dead. I make sure the filter is completelty clean. Why would it just stop? 3.) It seems like it is very repetitive. It sometimes just goes over the same area it already cleaned. Isn't it suppose to be "random" and clean the pool in its entirety? I don't want to have to fork out for some pool guy to come out and really want to try and do this pool thing on my own. Any help would be appreciated!!


Answer
Either get it looked at/repaired, or get a new one. Yes, it should randomly move around the pool, but it sometimes goes over the same spot multiple times. Also, sort of random, those things creep me out :). I refuse to go near them in the pool.

Are you a pool cleaner? Please help me pick a Kreepy Krauly...?




MagPookie


Should I get the Kreepy Krauly Classic or Kruiser model? The classic seems more popular although the kruiser supposedly works better. There's good and bad reviews for both and I just can't decide.

I have an irregular shaped fiberglass coated in-ground pool. My current one just died and it never could get in the corners or the stairs. Any info you can provide is appreciated. Thanks.



Answer
Both Kreepy Krauly models are very good automatic pool cleaners. I think that the classic is a better option, but either will work great.




Powered by Yahoo! Answers

Does anyone have an above ground pool automatic vacuum they can recommend?




thereshego


I have a 12 ft. easy-set intex pool and the only problem i'm having is getting the small algae particals that settle to the floor up after I've used algaecide and clarifier. I just have one of those cheap $12 vacuums and all it does is shuffle the algae around again. Can anyone recommend one and tell me approximately how much it is?


Answer
I wouldn't be without a Polaris pool cleaner. It is by far the best and we've owned several different ones.

New house - how do I take care of our pool?




Eric C


Details - Inground pool, approximately 70,000 gallons.


Answer
There's really not much detail here other than the volume. I could write a book and not cover what you need. If you post back with filter type, pool type (concrtet or vinyl), heater or no heater, type of sanitizer being used and any automatic pool cleaners, it would be helpful. There's simply too many things to cover other than basic water chemistry. I usually suggest to new home owners that they get a pool service guy in once, to give them waht our company calls pool 101's. Many service companies will do this for you and it won't cost much more than a service call (50 bucks). You'll get a personalized lesson, that's good for your specific set up and equipment. Take notes and if possible videotape the lesson. Hey, don't laugh, I think I'm starring in over 100 home videos by now. This way you can review what you've learned.
I'll go over some basics, common to most pools.
1/ check your chemistry at least once week. Total alkalinity 80-120 , Ph 7.2- 7.6, Cl or Br 1.0 -3.0. Always adjust your TA before trying to adjust anything else contrary to what I see in some of these posts ( still giggling, little wonder people's pools go green)
2/ Vac out the pool on at least a weekly basis. Keeping it clean helps lower your overall chemical expenditures.
3/ Clean out you pump and skimmer baskets on at least a weekly basis and same goes for whatever filter system you are using, unless it's a DE filter, you can leave those longer.
4/ Every month or so, take a water sample into your pool shop to be tested. They test for things a typical home owner's kit doesn't. If you're developing a calcium hardness issue, total dissolved solids or a dissolved metal issue, they can nip it in the bud before any damage occurs. You should also take in a sample 2 weeks prior to closing the pool (if applicable) and within a few days of pool opening (if applicable). Helps you put the pool to bed properly and get off to a good start in spring.
That's all I can post given the info you provided. Every pool is different. I'll put this on my watch list, if you update and may be able to help further.




Powered by Yahoo! Answers

Senin, 23 Juni 2014

Aqua EZ pool cleaner automatic or similar?




Jenn E


Anyone have this type of pool cleaner or this particular one that you can buy from Lowes does it work good? We really need one for our pool. How does it work? thanks

http://www.lowes.com/lowes/lkn?action=productDetail&productId=209556-1003-APC389&lpage=none



Answer
I bought that one a few years ago when my polaris went on the fritz. Don't waste your money on it. It is terrible. I found a place for parts on the internet and fixed my polaris. If you want something similar that works pretty well then look up automatic pool cleaners and look at Kreepy Krawly. That one works pretty well. I probably did not spell it right. Good luck.

we have a big pool and wondering what we can do to keep it clean?




motheroffo


we purchased a big pool and we bought the shock treatment chlorine tablets more filters leaf skimmer ect u name it but our pump went out we are waiting on another one but the water kindof stinks and its not clear like before. also how can we get the leafs that are on the bottom? do they make something special for that please help


Answer
A manual leaf net that you can use to scoop the leaves out would work. Also, an automatic pool cleaner would be a good option. One of these cleaners, along with proper shock and chlorine, should have your pool clean in no time.




Powered by Yahoo! Answers

Maintenance on an inground pool?




Em


I have never owned an inground pool and am looking to purchase a home that has one. However, I don't know anything about how much money, trouble, and effort it takes to keep one up, as far as maintenance. Please give me a clue...?


Answer
Keeping water in it helps, you also need to keep the water stabilized, proper PH, chlorine level, acidity etc. You will need to clean the filter or replace the media, which ever the case maybe, every 2-6 weeks or so depending on usage, if its screened in etc. It will also need to be vacuumed or you will have to get an automatic pool cleaner (which requires maintenance of its own). And eventually you will need to resurface your pool or deck, repair tile, replace your pool pump and filter, repair broken return or intake lines, repair the lighting. If you live in a climate where if freezes you will have to winterize your pool, whatever that entails. You also have to deal with homeowners insurance rules and local laws concerning safety fences, alarms and other things, I am sure I am forgetting something.

I don't mean to scare you....it's pretty easy to do most of these things, I spend about 1.5 hours a week at the most on my pool, and it is affordable if you do it yourself. If you don't want to do the weekly maintenance yourself get a pool service, in my area of Florida it is about $15-$20 a week and they check all of the water quality perimeters and add the appropriate chemicals (that you supply) and vacuum.

Can an automatic pool cleaner (a polaris) cause a leak?




Clharris20


I have an inground fiberglass pool and have been loosing about an inch of water a day. I read other answers and tried the bucket test and also marked the side of the pool with electrical tape to track.
I have noticed that my polaris has been shooting quite a bit of water out of the pool via splashing or getting stuck but the problem only began about a week and a half ago and I have had a polaris for years.
I completely shut the polaris off one morning before work just to test that theory. When I came home at the end of the day, the water level was fine! Then I turned the polaris on and after about an hour of running, the level dropped about a quarter of an inch.
I know water always flows through the polaris piping but could the surge in pressure after turning the polaris motor cause a minor crack to begin leaking?

Side note: my main drain line at the bottom of the pool has either clogged or collapsed but that has been the case for about a year and the pool has always looked crystal clear and maintained good water levels.
Any ideas or thoughts would be greatly appreciated! Thank you!



Answer
If the pool only leaks when the polaris pump is running it, it is almost certainly a break in the pipe between the booster pump and the pool. When the pump is running there is a lot mor pressure in the pipe so it will leak a lot quicker.
A leak detection company should be able to pin point where the leak is, and then a pool company can dig it up and fix it.

Look for wet soil in garden beds, etc. with the pump running.
Palm trees are the biggest culprit in breaking pool pipes.




Powered by Yahoo! Answers

my automatic pool cleaner is not working?




Justice


what should i do ro check out to see wny my automatic pool cleaner(polaris turtle) is not working?


Answer
I cannot find the website for polaris, seems they were sold not too long ago. I could be wrong on that.

If your turtle plugs into the skimmer or fitting in the water and there is not a separate pump to operate it, likely the turtle is a suction side automatic cleaner.

Suction side automatic cleaners all have something in common and that is when your filter is getting dirty the amount of water going through your cleaner and filter is way down. Inside your cleaner is a water paddle wheel that makes the turtle go.

Check your turtle to see if the passage ways are clean and clear and the hose is also, then clean out your filter. A clean filter should develop about 16-20psi when clean. When dirty and needing cleaning the pressure is about 26-30 or a 10 psi gain. Best to clean before 10 psi but surely by 10 psi.

You're welcome!!

What is the best automatic inground pool cleaner? What brand and price?




Francaise


Its a vinyl inground pool. Rectangular 18x36. Also budget is an issue, I am looking at spending $500 or less.


Answer
After 25 years of hearing how great floor head systems are, I have come to a conclusion. If your pool would have stayed looking nice with any cleaning system in your pool, it will stay nice with a floor head system.
If you plan on owning a pool for 5-6 years, or longer, in my opinion the best cleaning system(Dollar for Dollar) is a Polaris 280 with a booster pump and a separate time clock. The reasons are as follows:
1.)Low cost of repairs. I have clients with Polaris 180âs that are 25 years old. (The 280 has the same drive system.) Total repair costs in 25 years are less than $300.00 total (Not counting bag replacements.) I Personally, have owned a Polaris 280 for almost 5 years and have not spent a dime. (other than on 2 bags, and one of them was torn by my kids, and the other by a big pine cone. )

2.)It will clean most pools spotless in 10-20 minutes per day. You have seen our (5) 40â plus Ponderosa pines that overhang our pool area. Not counting steps and love seat, if we keep the bag cleaned, the floor stays spotless.

3.)Initial installation costs should be in the $1400.00-1600.00 range. Floor head systems are usually about double the initial expense. Also, the motor for the cleaning system is usually a 2 H.P. or larger, and the pool needs to run for substantially greater times to even get close to what a Polaris will do in ½ hour or less. Also, if you are not the initial purchaser of the system, you will not get a lifetime warrantee. Replacement gear systems, floor heads, ⦠can average more than $200.00 per year after the first 2 year, not to mention if the cleaner is not working correctly, i.e. heads jammed in the up position, actuator gears jammed, ⦠you are running that large motor with absolutely no cleaning going on. Any way you look at it, running a ¾ H.P. booster motor for 20-30 minutes is going to be a lot cheaper than running a 2 H.P. for 3-4 hours. Add into this that most motors run for more than 2 hours per day seem to have a life span in the 5-6 year range, and that a 2 H.P. motor is about double the cost, I cannot see spending the money.

4.)Suction side cleaners have a lower initial cost, but are annoying because either they will not pick up sticks, twigs, small rocks, ⦠or they will, and then they will completely stop working until you spend 10 minutes pulling them out and cleaning the debris out of them. Some of these will end up needing replacement parts just because of punctured diaphragms, ⦠This is in addition to an average annual repair cost of about $200-250, after the first year or two. In less than 5 years(More likely 3 years), if you add in electricity savings, pool cleanliness and thus chemical costs savings, and electrical savings, you have more than paid for the Polaris. If you add to this the fact that, if you have a suction side cleaner, you will have had to bring it in to the shop at least 4-5 times, having a non-functional cleaning system, thus a horridly dirty pool at least 4-5 times, the fact that often it dies a slow death each time so your pool doesnât look right for months prior to each rebuilding, and the repeated hassles of needing to unplug the system when ever any ârealâ debris ends up in the pool, and I wonât have anything else in my pool, or my families pools. To summarize, If you are buying a cleaner and are selling the home quickly, I would probably go with a pool Vac(if there are no rocks, sticks, big leaves, ⦠In other words, dirt only, but your annual repair costs will be high) or a Kreepy Krauley if you have anything else(Or want 40% less repair costs than the Pool Vac).

5.)Floor heads, or suction cleaners destroy the natural water flow around the pool which is responsible for moving the debris around to the skimmer on the surface, and for moving silt, and dirt to the main drain. Therefore, the surface areas of both sides of the pool(If the cleaners are functioning properly) will be an average of 20-40% dirtier than the same pool with a pool vac, return lines properly adjusted, and approximately ¾ of the suction of the pool going to the main drain. Also, since almost all of the suction for a suction side cleaner is directed to the cleaner, and thatâs run through an extra 30 feet or so of corrugated hose, the water flow is greatly reduced, and to get the same water filtration you will need to run that system approximately 25% -30% longer than a system without a suction cleaner. Thatâs 1 ¾ hrs longer running a 1 H.P. motor than is needed to run the ¾ H.P booster. Also, as a suction cleaner picks up debris, assuming it doesnât get plugged up and stop functioning all together, the baskets will fill up and all the suction to the pool will decrease or stop. There are times during the year where about 60% of the repair work I do is related to suction cleaning systems picking up too much debris. Note: This is never covered under any warrantee.

There is more that I could add, but I am too tired to do so now. Installation is as follows:




Powered by Yahoo! Answers

I'm looking to buy an automatic pool cleaner for an in-ground pool. Any suggestions on best brand and type?




Lynn





Answer
You didn't mention your budget. If you're looking to spend 300 dollars or under, then from a service guy's point of view on effectiveness, cost, ease of repair, least things that go wrong with them, it's a Kreepy Krauly, hands down.
Sure Baracudda markets itself as having no moving parts, but the one part that does all the action also wears out on a yearly basis. If you ask me, it's also a moving part, so their literature is pretty misleading.
If you're budget allows spending over a grand, then the Polaris vac sweep 360 or 380 is most certainly the way to go. The only issue here is if your pool currently has a plumbing line going to the pool it can use. Without one, you'll have to go the over deck route, which then is a hose to trip over, lying on the deck. That's the only drawback.
These two cleaners are totally different in their collection and operation. The Kreepy uses suction side plumbing (debris to the pump basket and filter), the Polaris uses pressure side, with it's own booster pump and it's collection is a bag attached to the Polaris head.

I have an automatic pool cleaner that looks like a ladybug that doesnt work.?




lanamerlit


She will suck dirt but will not move. If anyone has any ideas please let me know. They are expensive and I would like to repair before I buy a new one. Thanks.


Answer
Try asking this in the SWIMMING AND DIVING section. This is POOL & SNOOKER




Powered by Yahoo! Answers

Minggu, 22 Juni 2014

Storage unit problem pleas help ?

Q. Okay so I have recently rented a storage unit for my pool supplies because I own a pool cleaning service and keep it there i go there often but every time I go there is a pice of equipment moved like it was thrown againts the wall. So I told the manager and he said he would keep a look out. So I was on vacation and when I checked up on it the unit was comletly ransacked. I told the manager what had happened and he said that every night he here'd some loud noises coming from it but he couldn't get in (I have the only key) then he let my even review the security tape and you can see the unit doors shaking violently. So I had had enough and I put a camera in it. The results where shocking. You can see in the footage a white mist moving all around the unit and moving things around. I showed the manager the footage and he said that he did not know what it was. What could it be? I moved my stuff t another unit and it happened again. I can't move locations because there is not a rental place for miles.


Answer
Contact someone at http://www.paranormalsocieties.com and let them know about your video footage. (Assuming you're not trolling for fun ;)

Storage unit problem?

Q. Okay so I have recently rented a storage unit for my pool supplies because I own a pool cleaning service and keep it there i go there often but every time I go there is a pice of equipment moved like it was thrown againts the wall. So I told the manager and he said he would keep a look out. So I was on vacation and when I checked up on it the unit was comletly ransacked. I told the manager what had happened and he said that every night he here'd some loud noises coming from it but he couldn't get in (I have the only key) then he let my even review the security tape and you can see the unit doors shaking violently. So I had had enough and I put a camera in it. The results where shocking. You can see in the footage a white mist moving all around the unit and moving things around. I showed the manager the footage and he said that he did not know what it was. What could it be? I moved my stuff t another unit and it happened again. What could it be


Answer
Storage Wars-The Supernatural Edition




Powered by Yahoo! Answers

Sabtu, 21 Juni 2014

what is the best above groung automatic pool cleaner?




chris j


what do u guys and gals think the best above ground AUTOMATIC pool cleaner is the best. i have a baracuda zippy now it did ok for a while now its just dead. please give me some SERIOUS answers. i know my kids can do it. im looking for some advice. thanks you in advance.


Answer
I do realize you said serious advice ... but I can't help myself. Actually I have a "spider" cleaner that I sometimes have used in my above ground pool - BUT ... in all seriousness - I now have a "pool boy" ... not the speedo kind - but a gentleman that comes weekly from my pool chemical supply place for a cost of only $35 weekly + chemicals. Money well spent! Just wanted to let you know to check into it because it is probably more affordable than you realize. The fellow brings chemicals and adds them as needed and that cost then is added to my charge ticket.

It is nice to not have to worry about time consuming (although relaxing) cleaning. It never gets out of hand due to weather or heat etc. All we have to do is come in from work & enjoy the water.

Good luck.

Can anyone tell me what the best automatic in-ground pool cleaner is?




kittenscla


I just got an in-ground pool and am looking to purchase an automatic cleaner. I haved checked out all the info I can, but can't seem to come to a decision! I don't want to spend $700-$1000 on a product only to find out it doesn't work! I don't mind spending the money if I know it's going to be worth it!


Answer
Depends on the kind of dirt you need to pick up. Generally speaking, "suction side" cleaners that constantly vacuum your pool (hose goes into your skimmer) are best when you have mostly dust and dirt. They tend to have difficulty with larger debris like leaves and needles. If that is you main debris then I suggest a "pressure side" cleaner. Some of these have a booster pump, some don't. But they all use a hose with water pressure to propel them. They have a debris bag that will collect the leaves very well, but dust and dirt may go through the bag.




Powered by Yahoo! Answers

Automatic in ground pool vacuum?




Jessica Ra


Hello everyone,

I was wondering which automatic in ground pool vacuum is good for cleaning?

I am looking for something cheap and reliable, anyone have any experience with some good vacuum cleaners which does the job.

Thanks,
Jessica



Answer
i own a pool company and your better automatic pool vaccums would be either a polaris or a creepy crawly but you can get them cheaper online then in a pool store. look under pool companies

where can i find reviews of automatic swimming pool cleaners (like dolphin, aquabot, etc)?




john h





Answer
I chcked out the links in the answers above me and found a stange site that said nothing but had lots of google ads.The first thing you must decide is what TYPE of cleaner you want:

1)a pressure type cleaner (runs off of water pressure,usually its own pump,attached to your pool return plumbing)

2)a suction type cleaner that is attached to your skimmer or suction plumbing

3)a self powered cleaner that you plug in or recharge and throw in pool.

when you have decided what type you want,then a decision can be made as to which is the best...pressure types are good for leaves...suction types are cheaper and good on dirt,self powered units are more expensive...I have a website I just put up this january..in a few weeks,I will have photos and information there regarding pool cleaners: http://swimming-pool-information.com




Powered by Yahoo! Answers

Regression Problem- Confim my Anwers Please?




sabunabu


Please see the below and my answers-- please let me know if you disagree and also if you know the answers to the 2 questions I don't. Any help is greatly appreciated.

PoolVac, Inc. manufactures and sells a single product called the âSting Ray,â which is a patent-protected automatic cleaning device for swimming pools. PoolVacâs Sting Ray accounts for 65 percent of total industry sales of automatic pool cleaners. Its closest competitor, Howard Industries, has captured 18 percent of the market.

Using the last 26 months of its sales data, PoolVac wishes to estimate demand for its Sting Ray. Demand for Sting Rays is specified to be a linear function of its price (P), average income for households that have swimming pools in the U.S (MAVG) and the price of the competing pool cleaner sold by Howard Industries (PH). The general linear form of the demand function

Qd = a + b P + c MAVG + d PH.

The attached computer printout presents the regression output from 26 observations (monthly data) on the price charged for a Sting Ray (P), average income of households with pools (MAVG), and the price Howard industries charged for its pool cleaner (PH).
âââââ ââââââââââââââââââââ
The printout of part of regression output from Minitab for the empirical demand is below:

Regression Analysis: Q versus P, MAVG, PH

Predictor Coef SE Coef T P
Constant 2728.8 531.7 5.13 0.000
P -10.758 1.330 -8.09 0.000
MAVG 0.021420 0.009452 2.27 0.034
PH 3.166 1.344 2.36 0.028

S = 73.0546 R-Sq = 96.6% R-Sq(adj) = 96.2%

Analysis of Variance

Source DF SS MS F P
Regression 3 3379846 1126615 211.10 0.000
Residual Error 22 117414 5337
Total 25 3497260

Source DF Seq SS
P 1 3327368
MAVG 1 22878
PH 1 29600


ââââââââââââââââââââââââââââ
1. An estimated demand equation for PoolVac is:
Qd = 2728.8-10.758P+0.021420M+3.166Ph


2. Evaluate the statistical significance of the three estimated slope parameters using a significance level of .05 or 5 percent (you can either use p-values or do a t-test).Please, explain how you decided each parameter was statistically significant or not.

Since the P values of all 3 variables are within the 5% confidence interval, each variable should be considered as staristically significant in determining the demand of the pool vacuums.


3. What is the exact level of statistical significance for estimated slope parameters on price, average income of household and price of related good? Please, explain how you know.

We should look at the P value for each of the slope parameters and in doing so, we find that price is 100% significant, average income (Mavg) is 96.6% (100-.034) and price of competition (Ph) is 97.2% significant (100-.028).


4. Discuss the appropriateness and/or interpretations of the algebraic signs of the three slope parameters, based on your theoretical expectations. Interpret the numerical values of the three slope parameters in the context of this regression.


5. Now evaluate the overall fit of the estimated (sample) regression equation to the data.

a. What percentage of variability in Qd (linear) is explained by a model? Does it indicate a good overall fit? Please, explain.


b. Verify whether the overall regression equation is statistically significant, another words, verify the goodness of overall fit .What is the exact level of significance for the entire regression equation?

Looking at the F stat which is 211.1, we can say the overall regression equation is significant since the absolute value is large. Also, the P value is 0 so there is no chance that this regression equation doesnât explain the relationship between the given variables and quantity demanded.



Answer
All of your answers are good. To say that the F statistic has a large absolute value is a little vague; one would generally either consult an F table to the appropriate threshold value or just look at the P value in the computer output. On the other hand, it isn't wrong, and if your instructor taught it that way you should leave it in.

Regarding the questions you haven't answered, number 4 refers to the direction of the effects on your dependent variable that come with changes in the independent variables. You should look at your coefficients and consider what would happen if you changed the values in your variables. For example, if the price of the product goes up, demand for the product goes down because of the negative coefficient associated with the price variable. If this seems confusing, try plugging in some different values into the equation and calculating the result. The negative coefficient makes sense, because people are going to be less interested in buying something if its more expensive. The question is asking you to evaluate both the actual effects on demand and the expected effects for each of the variables.

Question 5a refers to the R-squared statistic (R-Sq), which is the percent of explained variability as mentioned in the question. Yours is quite high.

How do you get rid of efflorescence on Pavers/Stones?




CuriousJor


My steps were built using Rinox pavers and I've got alot of efflorescence on them. The contractor told me that this was a normal process from the concrete curing process and that it goes away after a short while. It's almost 3 years later and It's still there. Does anyone know if this is going to go away or how to treat it. I find it so unattractive everytime I look at it.

Thanks



Answer
Cleaning and Sealing Paving Stones

STONESAVER® premium concrete surface cleaners, water repellent and sealers have been formulated to provide the best cleaning, preparation and sealing system on the market. Originally developed for the commercial paving surface industry, STONESAVER® products have been put to the test by many satisfied professionals for years before finally being offered to the retail public.



Rust Remover.

Removes stubborn rust stains from paving stones and concrete.


Citrus Oil Degreaser

Uses a unique blend of citrus extracts to removes oil and grease stains from paving stones and concrete.


Stripper

Removes paint, graffiti, rubber, tar and chewing gum from paving stones and concrete.


Cleaner and Surface Prep

Essential pre-sealing surface preparation ensures vibrant colour and proper sealer to surface bonding.
Removes efflorescence, dirt and tire marks from paving stones and concrete.
Complete with E-Z Spray auto mixing hose adaptor.


Paving Stone Sealer

Protects paving stones against salt, oil, rust, acid rain, UV colour fading and pool chemicals.
Premium formulation, high acrylic solids.
Colour enhancing wet look.
Will not peel, wears evenly.
Comes in 3.78L and 18L containersâ 1L covers 30 to 40 square feet.


How Long to Wait Until Sealing



Sealing should be done only after the natural efflorescence process has been given time to take place. Efflorescence, being a whitish powder, is the deposit of small quantities of cement from within the pavers on its top surface after a series of wetting (rainfall) and drying (warm weather) cycles. Because a series of wet/dry cycles are required, which are weather dependant, there is no exact time frame which applies to every situation. However, allowing 8 weeks, with a minimum of 4 precipitation events during that time, is a common rule of thumb.



Stain Removal

Between installation and sealing, some pavers may become stained due to foot and vehicle trafficâ this is common. However, it is important to remove these stains prior to sealing or else their appearance through sealing may become enhanced.



The first step is to inspect for any extremely stained, cracked or broken units which should be replaced. All items which cast shadows on the area (e.g. furniture) should be removed, if possible, to allow the area to dry evenly once stain removal and cleaning is completed. Similarly, automatic sprinkler systems should be turned off during cleaning and sealing operations.



Prior to using any of these products, refer to the respective productsâ

labels for personal protection, installation and first aid suggestions.



Start stain removal at the bottom of the pavement and work up the slope in manageable sections. This prevents untreated areas from becoming wet, which can hide some stains.



Rust Remover- Pre-wet the stained area with water. Apply a liberal amount of the stain remover to the stained area only and let stand for two minutes. Vigorously scrub the stain with a stiff bristle scrub brush and rinse immediately with generous amounts of water. Repeat if necessary.



Citrus Oil Degreaserâ Pre-wet the stained area with water. Apply a liberal amount of stain remover to the stained area and let stand for one minute. Vigorously scrub the stain with a stiff bristle scrub brush and rinse away cleaner and residue thoroughly with water (strong water pressure works best). Stains that have deeply penetrated into the pavers may resurface after initial cleaning and dryingâ repeat stain removal process if necessary.



Stripperâ Remove excess material with a scraper. Apply sufficient Stripper to cover the remaining stain. Allow product to stand for approximately 5 minutes. Do not let product dry on surface. Scrub stained area with a stiff bristle brush. Rinse thoroughly with water (strong water pressure works best). Repeat if necessary.



When all stains are removed, rinse the entire area down to ensure any residuals are washed away.



Cleaning Process



Once the stains are removed, the entire area should be thoroughly cleaned to remove any efflorescence and dirt. Note: Because of the effectiveness of the Surface Cleaner, spot cleaning will be noticeable in the final product; therefore, it is recommended that the entire area be cleaned.



Prior to starting each application, lightly pre-wet the area with water, as well as any vegetated areas that may be subject to overspray and/or runoff. As a precaution, delicate vegetation can be pulled back or covered to protect from overspray.



Concrete Cleaner- Simply attach your water hose to the inlet port of the E-Z sprayer and you are ready to start. Working quickly, start at the lowest point of your surface and work in 27 square metre (300 square feet) pre measured sections. Work side to side, making sure the entire surface is covered. If there is still cleaner remaining in the bottle after the section is done, apply the remaining cleaner as an additional spray over the same areaâ this will reinforce the cleaning application and prevent drying of the surface. Use a long handled stiff bristled broom to brush the treated area, loosening stubborn dirt and deposits. Rinse thoroughly (usually 5-6 rinses with a pressure sprayer until foaming is no longer visible. However, care should be taken to not blow or wash the sand from the jointsâ sand will remain in the joints if a wide spray nozzle is used and the angle of the spray is kept from directly penetrating the joints. Be sure to rinse all cleaner from the surface as you progress to additional sections until the entire surface is cleaned and thoroughly rinsed. Do not let the cleaner dry on surface or stand in low spots as this may stain the pavers; mist surface with water if it begins to dry.



When the entire surface is cleaned and well rinsed, allow to dry and inspect. Repeat application to the white (efflorescence) areas if necessary.



For vegetated areas that were subject to overspray or runoff, dilute the areas one last time with large quantities of clean water.



Sealing

Allow at least 24 hours without moisture or surface dampness before sealing. If the pavers and jointing sand are not totally dry (not just surface dry), moisture blushing may occur under the sealer after it is applied, or the sealer may become cloudy/white.



Never re-sand paving joints between cleaning and sealing applications as this will leave residue on the surface of the pavers.



Paving Stone Sealerâ For best results, use a lint free high pile roller and a metal paint tray, or airless sprayer, to apply the sealer. Apply at a temperature above 7 Degrees C (45 Degrees F). Apply sufficient sealer to fully saturate the surface and penetrate at least 15 mm (5/8â) into the jointing sand. Excess sealer on the surface should be pushed to an unsealed area with a rubber squeegee, which are effective in achieving good penetration but avoid bringing jointing sand to the surface of the pavers.



For surfaces being sealed for the first time, apply a second coat by rolling in a cross direction from the first coat. Allow one hour to dry between applications. Allow sealed surfaces to dry for 24 hours before using.




Powered by Yahoo! Answers

Jumat, 20 Juni 2014

how do above ground automatic pool cleaners work??




Hugeez





Answer
the most common form of pool cleaners are suction cleaners which have a hose that simply attaches through the skimmer. (If the pool has a main drain, it would need to be closed using the valve). The cleaner automatically moves around the bottom of the pool, sucking debris off the bottom of the pool and trapping it in the pump basket and filter. The pump basket should be emptied before and after the cleaning cycle. And the filter should be cleaned after cleaning the pool. Any large debris (leaves, sticks, and such) should be removed from the pool with a leaf rake before hooking up cleaner to prevent clogging up plumbing and allowing for a more effecient cleaning cycle. If you are considering purchasing a cleaner, I highly recommend the Zodiac brand. ( By the way, incase you're wondering, I own a swimming pool company and would be more than happy to answer any other questions you may have)

I am looking to purchase an automatic pool cleaner, any suggestions? ?




Chris


I have an in-ground vinyl liner pool that is 17x36. At its deepest point, it is 8.5 feet deep with sloped walls and tight corners going down. (Someone called it a diving pool?) I want one that is self contained and doesn't hook up to my filter. I was originally looking at the Dolphin Diagnostic Advantage (DL2019) In-Ground Robotic Pool Cleaner but am open for suggestions. Anyone have any experience with these or can throw me some pros or cons of a different type? I am not willing to spend more than a $1,000.00.


Answer
Look at any of the Polaris products. They come in several different types of pool cleaners and price range.


Google:

Reviews and prices on automatic pool cleaners.



:-)




Powered by Yahoo! Answers

Kamis, 19 Juni 2014

what cleaning pads can i use to clean my swimming pool?




Sue





Answer
There aren't really any cleaning pads designed for swimming pool use. To clean your swimming pool, you need to have balanced pool chemicals and an automatic pool cleaner. You can also use a brush designed to scrub pool walls.

Asking price for a 27 foot above ground swimming pool?




Dain K


I have a 27 foot above ground swimming pool (3 years old) that I am trying to sell. It is in very good condition with a pump/filter, solar and winter covers, and accessories such stairs and automatic cleaner. The liner is fine now, but it may need to be replaced when torn down, but no idea. Is $1500 too much to ask? $1000? $500? I'm clueless on this.


Answer
Dain, i already answered your question on this with your other question when you referred to your pool as a 24 foot Round pool.

I gave it a second thought after posting, and seeing this message, IF you want to sell your pool, or get rid of it, you might want to post an ad for used pool equipment. A Pump/motor usually goes for 3-400 bucks, and the filter could be a few hundred more, but the equipment is used, so if you get someone to buy it for 500 dollars you should consider yourself lucky. Place an add for the equipment, and as a bonus they can have the pool for free. you might get a taker, But refer to my other message where i talked about liability. You don't want to be held responsible when the pool leaves your yard, so should something happen in 2 weeks, whether it is faultyequipment or improper installation, just make sure you dont get caught up in it.

It makes no sense to try and make a few bucks back on your pool that is 3 years old, and then by some string of bad luck, have someone come knocking on your door looking for damages because the ladder or steps failed and someone got injured. Sure it could be from the new owner installing equipment improperly, and you have no control over it, But is it really worth the hassle? Sell your used equipment, people will buy it. Especially now where people are going to have equipment failures and problems from the past winter, and dismantle your pool and put it on the side of the road, i guarantee someone will load it and take it away, even if there is no equipment.




Powered by Yahoo! Answers

Looking to buy a house, it has a pool but no equipment. Its a standerd size kidney shaped pool, max depth 6ft.?




haque_ss





Answer
Are you asking what type of equipment you will need? If so, you will need a pump and filter system if there is not one already there. You will need an automatic pool cleaner. You will have to have pool chemicals. There are other optional things, like pool heaters, that are useful, but you cannot get your pool operational without a filter, pool cleaner, and chemicals such as chlorine.

Pool plumbing clogged?




Lynn


My 3 year old dropped a carrot in the pool and the automatic vacuum sucked it up. Now the automatic cleaner is running very slow. Is it the actual vacuum or the plumbing that is clogged?


Answer
If this is a pool sweep that crawls around in the pool sucking up debris I can assure you the carrot is in the vacuum itself. Turn it off, haul it out of the pool and empty the container or bag. If this is one of the new vacuum systems that have water jets sequentially pushing the debris to one area where a drain opens and captures the debris you may or may not have clogged plumbing. That type of system has a filter basket somewhere to catch large objects before they get to the pump and other equipment. You need to check that and any other baskets such as the skimmers and the basket on the pump itself. If you know for sure the carrot got into the plumbing itself and it doesn't show up in any of the baskets, etc., you may have to fish it out. But, since carrots are organic matter the thing will eventually decompose and make it's way to the filter.




Powered by Yahoo! Answers

Drain in ground pool with a vinyl liner?







I'm stuck between a rock and a hard place with this situation. My pool has become like a swamp, literally. It hasn't been cleaned in a year and a half and has become a mating ground for frogs. It is black! I had the idea to drain the pool, clean it, and refill it. The pool guy that installed the pool told me this was a bad idea. He said that if I drain the pool, it will collapse due to high ground water. Understandable, I live two blocks up from the ocean. From all the websites and forums I have read, it doesn't seem like it will collapse immediately. I cannot run the pump to circulate "shock" because of all the leaves at the bottom. I cannot see the leaves at the bottom to clean them because the water is black. I figured draining and scooping the crud out would be the best idea. If I did this in a matter of a weekend, would I be safe? It is my fault, and I take complete responsibility. I would like to save money where I can and not have to pay a professional to do this. I can rent a sump pump to drain it, and just use my hose to refill it. My husband said the liner needs to be scrubbed down because of all the algae. Please help! :(


Answer
It is never a good idea to drain in completely. I would drain it partially (about 2/3 of the water) and start cleaning from there. Scoop out as much of the debris as you can, refill the pool, run your filter, and shock the pool several times with pool chemicals. If you liner has been exposed to all this debris, etc., it might also need to be replaced. If you have an automatic pool cleaner, make sure that you run it frequently while you are trying to get everything back in tip top shape.

how much does an inground pool cost?




limetemple


medium size


Answer
Medium size would be an 18 x 36. Costs of construction can vary enormously. Expect that size pool to start at about 18,000 canadian dollars for a vinyl inground. A concrete (gunite) pool would be about 28 grand to start.
Extra costs can be incurred if the access to the dig is difficult, material has to be trucked father away to dump, if the area the dig is in is in a high water table or is very rocky.. The toys you want with the pool, like water falls or adjacent hot tubs. The pool equipment packages can vary from basic to hi tech advanced remote wall unit controls in the house for heat, automatic pool cleaner controls and even one touch and forget, timed pool fill valves.




Powered by Yahoo! Answers

what is the best above ground pool automatic vacumn?




buddysher3


i have a 24 round pool what like some feedback on automatic cleaners there are so many choices


Answer
Have you tried doing the "sneaky" thing... call around to pool cleaners and ask them what equipment they use to clean the pools? If they have any recommendations for automatic vacuums? Trust me, as a house cleaner, if anyone calls me and asks for my advice as to what equipment I think is best, I wholeheartedly give them my recommendations.... both pro and con! I'm sure you can find some leads if you ask!

Good Luck!

does anyone know how to fix a robo Kleen above ground pool cleaner?




IBnkc


My Robo Kleen automatic above ground pool cleaner worked at first, then it began running a little forward and a little backwards then it stopped altogether?


Answer
Is this the one that runs on pool suction ? I had one that ran that way and it would clog up if leaves or debris got in it.




Powered by Yahoo! Answers

What is the best automatic inground pool cleaner? What brand and price?




Francaise


Its a vinyl inground pool. Rectangular 18x36. Also budget is an issue, I am looking at spending $500 or less.


Answer
After 25 years of hearing how great floor head systems are, I have come to a conclusion. If your pool would have stayed looking nice with any cleaning system in your pool, it will stay nice with a floor head system.
If you plan on owning a pool for 5-6 years, or longer, in my opinion the best cleaning system(Dollar for Dollar) is a Polaris 280 with a booster pump and a separate time clock. The reasons are as follows:
1.)Low cost of repairs. I have clients with Polaris 180âs that are 25 years old. (The 280 has the same drive system.) Total repair costs in 25 years are less than $300.00 total (Not counting bag replacements.) I Personally, have owned a Polaris 280 for almost 5 years and have not spent a dime. (other than on 2 bags, and one of them was torn by my kids, and the other by a big pine cone. )

2.)It will clean most pools spotless in 10-20 minutes per day. You have seen our (5) 40â plus Ponderosa pines that overhang our pool area. Not counting steps and love seat, if we keep the bag cleaned, the floor stays spotless.

3.)Initial installation costs should be in the $1400.00-1600.00 range. Floor head systems are usually about double the initial expense. Also, the motor for the cleaning system is usually a 2 H.P. or larger, and the pool needs to run for substantially greater times to even get close to what a Polaris will do in ½ hour or less. Also, if you are not the initial purchaser of the system, you will not get a lifetime warrantee. Replacement gear systems, floor heads, ⦠can average more than $200.00 per year after the first 2 year, not to mention if the cleaner is not working correctly, i.e. heads jammed in the up position, actuator gears jammed, ⦠you are running that large motor with absolutely no cleaning going on. Any way you look at it, running a ¾ H.P. booster motor for 20-30 minutes is going to be a lot cheaper than running a 2 H.P. for 3-4 hours. Add into this that most motors run for more than 2 hours per day seem to have a life span in the 5-6 year range, and that a 2 H.P. motor is about double the cost, I cannot see spending the money.

4.)Suction side cleaners have a lower initial cost, but are annoying because either they will not pick up sticks, twigs, small rocks, ⦠or they will, and then they will completely stop working until you spend 10 minutes pulling them out and cleaning the debris out of them. Some of these will end up needing replacement parts just because of punctured diaphragms, ⦠This is in addition to an average annual repair cost of about $200-250, after the first year or two. In less than 5 years(More likely 3 years), if you add in electricity savings, pool cleanliness and thus chemical costs savings, and electrical savings, you have more than paid for the Polaris. If you add to this the fact that, if you have a suction side cleaner, you will have had to bring it in to the shop at least 4-5 times, having a non-functional cleaning system, thus a horridly dirty pool at least 4-5 times, the fact that often it dies a slow death each time so your pool doesnât look right for months prior to each rebuilding, and the repeated hassles of needing to unplug the system when ever any ârealâ debris ends up in the pool, and I wonât have anything else in my pool, or my families pools. To summarize, If you are buying a cleaner and are selling the home quickly, I would probably go with a pool Vac(if there are no rocks, sticks, big leaves, ⦠In other words, dirt only, but your annual repair costs will be high) or a Kreepy Krauley if you have anything else(Or want 40% less repair costs than the Pool Vac).

5.)Floor heads, or suction cleaners destroy the natural water flow around the pool which is responsible for moving the debris around to the skimmer on the surface, and for moving silt, and dirt to the main drain. Therefore, the surface areas of both sides of the pool(If the cleaners are functioning properly) will be an average of 20-40% dirtier than the same pool with a pool vac, return lines properly adjusted, and approximately ¾ of the suction of the pool going to the main drain. Also, since almost all of the suction for a suction side cleaner is directed to the cleaner, and thatâs run through an extra 30 feet or so of corrugated hose, the water flow is greatly reduced, and to get the same water filtration you will need to run that system approximately 25% -30% longer than a system without a suction cleaner. Thatâs 1 ¾ hrs longer running a 1 H.P. motor than is needed to run the ¾ H.P booster. Also, as a suction cleaner picks up debris, assuming it doesnât get plugged up and stop functioning all together, the baskets will fill up and all the suction to the pool will decrease or stop. There are times during the year where about 60% of the repair work I do is related to suction cleaning systems picking up too much debris. Note: This is never covered under any warrantee.

There is more that I could add, but I am too tired to do so now. Installation is as follows:

How to connect an automatic pool cleaner (Cruiser C400).?




Cat


Should the pump be set to filtration or circulation? and should both the skimmer and bottom valves be left open?


Answer
Close the bottom drain. If your pool has a side drain, connect the pool cleaner there. If not, put a y-fitting into the skimmer and tie your pool cleaner in there. Set the pump for filtration to take out the stuff the pool cleaner picks up.

My neighbor tied his pool cleaner into one of the bottom drains and plugged the other. That seems to work ok too but you have to fool around with the balance between the two drains to get the pool cleaner to work.




Powered by Yahoo! Answers

What's the best automatic above ground pool cleaner to buy?




mkskipp44





Answer
Check out poolgearplus.com they have some pretty neat stuff there. I just clean mine with the pump vacuum.

In-experienced pool care...when I hookup automatic cleaner do I put on backwash to vacuum or regular pump?




JuJu





Answer
i own a pool company MICMAN is wrong you want to turn your pool on to filter. i have done pools for fourteen (14) years.put your pool pump to filter to vaccum pool




Powered by Yahoo! Answers

what is the correct vacuuming equipment for a 10,000 gallon pool?




generallee





Answer
It depends on what kind of vaccuming you want. Automatic or manual. There are several choices for automatic pool sweepers. Some work off the suction side of your filter, and others use the return water for power.
For manual vacuuming, you will need a pole, vacuum hose, and vacuum attachment. There are two types of vacuum attachments, one is for vinyl lined pools(has brushes on it instead of wheels), one is for standard gunnite pools (has wheels on the bottom).
To vacuum manually: First turn on your filter. Attach the vacuum attachment to the pole, then one end of the hose to the attachment. Hold the hose and insert the vacuum head attachment into the water. Let it sink to the bottom, then keep feeding the hose into the water. This will fill the vacuum hose with water. When you get the entire hose filled with water, insert the end into the skimmer hole that sucks water into the filter. Make sure you get a vacuum hose that's long enough to reach all areas of the pool.
For help selecting an automatic pool cleaner, see your local pool store. Hope this helps.

What Chemicals Should I Use To Remove Green Algae From My Swimming Pool?




kenne727


My pool has been looking very green lately. I have noticed that the bottom (the floor) and the walls of the pool are frequently greenish and needs to be vacuumed very often. But I want to know why this is the case. Is this because of algae growing? What chemicals should I buy. I know that shock and phosfree is needed. What effect will these chemicals have on the algae and water, and what do these chemicals do?

Thank you



Answer
Every pool owner has, at one time or another, done battle with the occasional algae bloom. Algae spores constantly enter the pool, brought in by wind, rain or even contaminated swimsuits or equipment.
Algae are a living aquatic creature that multiplies rapidly on warm, sunny days. Containing chlorophyll, algae utilizes photosynthesis to grow. That is, they take in carbon dioxide and expend oxygen as a byproduct. There are over 21,000 known varieties of algae and they classified into colors âgreen, yellow, black, pink.
Proper chemical balance and sanitizer residuals will prevent many opportunities for algae to bloom. High pH and low chlorine (or other sanitizer) can give algae a great start to genesis. General cleanliness of the pool is also important. Organic material and bacteria can contribute to algae growth.
Regular brushing of seemingly clean pools is not only good exercise for you, but prevents dirt from harboring in the pores of the plaster, which is a good start for an algae colony. Add unstabilized clorine granules (shock) to the pool. the amount of chlorine you add will depend on the capacity of your pool (150gr/10,000L or approx. 5oz of chlorine/2500gal of water). Vacuum the white residue from the bottom of the pool the next day. Clean your filter to remove any alga residue. Rebalance your pool water.
The cause of reoccurring algae, especially if it keeps appearing in the same places, is poor circulation. Often we find the return(s) of the pool (where water reenters the pool from the filter system) directed towards the surface of the pool. Dead spots are areas where little or no water is circulating. Even with main drains, the returns pointed upward to the surface mean little or no circulation on the bottom or lower areas of the walls. This results in little or no algaecide reaching these spots and algae never really being eradicated.
The there are ways to increase the area of circulation is to run your automatic cleaner. Even when the pool is not dirty, it helps to bring clean, just running your cleaner once a week can make a big difference in preventing algae from reoccurring. The best




Powered by Yahoo! Answers

Rabu, 18 Juni 2014

Ways of conserving water?




Anugrah P


I have to write an essay on ways of conserving water and the difference it can make?
Please Help!



Answer
Tips for the Northwest
All | Indoor | Outdoor


#1. There are a number of ways to save water, and they all start with you.


#2. When washing dishes by hand, don't let the water run while rinsing. Fill one sink with wash water and the other with rinse water.


#3. Some refrigerators, air conditioners and ice-makers are cooled with wasted flows of water. Consider upgrading with air-cooled appliances for significant water savings.


#4. Adjust sprinklers so only your lawn is watered and not the house, sidewalk, or street.


#5. Run your clothes washer and dishwasher only when they are full. You can save up to 1,000 gallons a month.


#6. Choose shrubs and groundcovers, instead of turf, for hard-to-water areas such as steep slopes and isolated strips.


#7. Install covers on pools and spas and check for leaks around your pumps.


#8. Use the garbage disposal sparingly. Compost vegetable food waste instead and save gallons every time.


#9. Plant in the fall when conditions are cooler and rainfall is more plentiful.



#10. For cold drinks keep a pitcher of water in the refrigerator instead of running the tap. This way, every drop goes down you and not the drain.


#11. Monitor your water bill for unusually high use. Your bill and water meter are tools that can help you discover leaks.


#12. Water your lawn and garden in the morning or evening when temperatures are cooler to minimize evaporation.


#13. Wash your fruits and vegetables in a pan of water instead of running water from the tap.


#14. Spreading a layer of organic mulch around plants retains moisture and saves water, time and money.


#15. Use a broom instead of a hose to clean your driveway and sidewalk and save water every time.


#16. If your shower fills a one-gallon bucket in less than 20 seconds, replace the showerhead with a water-efficient model.


#17. Collect the water you use for rinsing fruits and vegetables, then reuse it to water houseplants.


back to top
#18. If water runs off your lawn easily, split your watering time into shorter periods to allow for better absorption.


#19. We're more likely to notice leaks indoors, but don't forget to check outdoor faucets, sprinklers and hoses for leaks.


#20. If you have an automatic refilling device, check your pool periodically for leaks.


#21. Check the root zone of your lawn or garden for moisture before watering using a spade or trowel. If it's still moist 2 inches under the soil surface, you still have enough water.


#22. When buying new appliances, consider those that offer cycle and load size adjustments. They're more water and energy efficient.


#23. Shorten your shower by a minute or two and you'll save up to 150 gallons per month.


#24. Upgrade older toilets with water efficient models.


#25. Adjust your lawn mower to a higher setting. A taller lawn shades roots and holds soil moisture better than if it is closely clipped.


#26. When cleaning out fish tanks, give the nutrient-rich water to your plants.


#27. Use sprinklers for large areas of grass. Water small patches by hand to avoid waste.


#28. Put food coloring in your toilet tank. If it seeps into the toilet bowl without flushing, you have a leak. Fixing it can save up to 1,000 gallons a month.


#29. When running a bath, plug the tub before turning the water on, then adjust the temperature as the tub fills up.


#30. Walkways and patios provide space that doesn't ever need to be watered. These useful "rooms" can also add value to your property.


#31. Collect water from your roof to water your garden.


#32. Designate one glass for your drinking water each day or refill a water bottle. This will cut down on the number glasses to wash.


#33. Rather than following a set watering schedule, check for soil moisture two to three inches below the surface before watering.


#34. Install a rain sensor on your irrigation controller so your system won't run when it's raining.


#35. Don't use running water to thaw food. Defrost food in the refrigerator for water efficiency and food safety.


#36. Use drip irrigation for shrubs and trees to apply water directly to the roots where it's needed.


#37. Grab a wrench and fix that leaky faucet. Faucet repair can save up to 300 gallons a month.


#38. Reduce the amount of lawn in your yard by planting shrubs and ground covers appropriate to your site and region.


#39. When doing laundry, match the water level to the size of the load.


back to top
#40. Teach your children to turn off faucets tightly after each use.


#41. Remember to check your sprinkler system valves periodically for leaks and keep the sprinkler heads in good shape.


#42. Use a water-efficient showerhead. They're inexpensive, easy to install, and can save you up to 750 gallons a month.


#43. Soak pots and pans instead of letting the water run while you scrape them clean.


#44. Don't water your lawn on windy days when most of the water blows away or evaporates.


#45. Water your plants deeply but less frequently to encourage deep root growth and drought tolerance.


#46. Know where your master water shut-off valve is located. This could save water and prevent damage to your home.


#47. To decrease water from being wasted on sloping lawns, apply water for five minutes and then repeated two to three times.


#48. Group plants with the same watering needs together to avoid overwatering some while underwatering others.


#49. Use a lawer of organic material on the surface of your planting beds to minimize weed growth that competes for water.


#50. Use a minimum amount of organic or slow release fertilizer to promote a healthy and drought tolerant landscape.


#51. Trickling or cascading fountains lose less water to evaporation, than those spraying water into the air.


#52. Use a commercial car wash that recycles water.


#53. Avoid recreational water toys that require a constant flow of water.


#54. Turn off the water while brushing your teeth and save 25 gallons a month.


#55. Use a rain gauge, or empty tuna can, to track rainfall on your lawn. Then reduce your watering accordingly.


#56. Encourage your school system and local government to develop and promote water conservation among children and adults.


#57. Learn how to shut off your automatic watering system in case it malfunctions or you get an unexpected rain.


#58. Set a kitchen timer when watering your lawn or garden to remind you when to stop. A running hose can discharge up to 10 gallons a minute.


back to top
#59. If your toilet flapper doesn't close after flushing, replace it.


#60. Make sure there are water-saving aerators on all of your faucets.


#61. By selecting plants suited to your yard's conditions, you'll use less water and other resources.


#62. Install an instant water heater near your kitchen sink so you don't have to run the water while it heats up. This also reduces energy costs.


#63. Use a grease pencil to mark the water level of your pool at the skimmer. Check the mark 24 hours later to see if you have a leak.


#64. If your dishwasher is new, cut back on rinsing. Newer models clean more thoroughly than older ones.


#65. Use a trowel, shovel, or soil probe to examine soil moisture depth. If the top two to three inches of soil are dry it's time to water.


#66. If installing a lawn, select a turf mix or blend that matches your climate and site conditions.


#67. When you save water, you save money on your utility bills too. Saving water is easy for everyone to do.


#68. When the kids want to cool off, use the sprinkler in an area where your lawn needs it the most.


#69. Make sure your swimming pools, fountains, and ponds are equipped with recirculating pumps.


#70. Bathe your young children together.


#71. Consult with your local nursery for information on plant selection and placement for optimum outdoor water savings.


#72. Winterize outdoor spigots when temperatures dip below freezing to prevent pipes from leaking or bursting.


#73. Insulate hot water pipes for more immediate hot water at the faucet and for energy savings.


#74. Wash your car on the lawn, and you'll water your lawn at the same time.


#75. Drop your tissue in the trash instead of flushing it and save water every time.


#76. Direct water from rain gutters and HVAC systems towards water-loving plants in the landscape for automatic water savings.


#77. Make suggestions to your employer about ways to save water and money at work.


#78. Support projects that use reclaimed wastewater for irrigation and industrial uses.


#79. Use a hose nozzle or turn off the water while you wash your car. You'll save up to 100 gallons every time.


#80. Share water conservation tips with friends and neighbors.


#81. If your toilet was installed before 1992, reduce the amount of water used for each flush by inserting a displacement device in the tank.


back to top
#82. Setting cooling systems and water softeners for a minimum number of re-fills saves both water and chemicals, plus more on utility bills.


#83. Washing dark clothes in cold water saves both on water and energy while it helps your clothes to keep their colors.


#84. Leave lower branches on trees and shrubs and allow leaf litter to accumulate on the soil. This keeps the soil cooler and reduces evaporation.


#85. Report broken pipes, open hydrants and errant sprinklers to the property owner or your water provider.


#86. Let your lawn to go dormant during the summer. Dormant grass only needs to be watered every three weeks or less if it rains.


#87. Plant with finished compost to add water-holding and nutrient-rich organic matter to the soil.


#88. Use sprinklers that deliver big drops of water close to the ground. Smaller water drops and mist often evaporate before they hit the ground.


#89. Listen for dripping faucets and running toilets. Fixing a leak can save 300 gallons a month or more.


#90. Water only when necessary. More plants die from over-watering than from under-watering.


#91. One more way to get eight glasses of water a day is to re-use the water left over from cooked or steamed foods to start a scrumptious and nutritious soup.


#92. Adjust your watering schedule each month to match seasonal weather conditions and landscape requirements.


#93. Turn off the water while you wash your hair to save up to 150 gallons a month.


#94. Wash your pets outdoors in an area of your lawn that needs water.


#95. When shopping for a new clothes washer, compare resource savings among Energy Star models. Some of these can save up to 20 gallons per load, and energy too.


#96. Apply water only as fast as the soil can absorb it.


#97. Aerate your lawn at least once a year so water can reach the roots rather run off the surface.


#98. When washing dishes by hand, fill the sink basin or a large container and rinse when all of the dishes have been soaped and scrubbed.


#99. Catch water in an empty tuna can to measure sprinkler output. One inch of water on one square foot of grass equals two-thirds of a gallon of water.


#100. Turn off the water while you shave and save up to 300 gallons a month.


#101. When you give your pet fresh water, don't throw the old water down the drain. Use it to water your trees or shrubs.


#102. If you accidentally drop ice cubes when filling your glass from the freezer, don't throw them in the sink. Drop them in a house plant instead.


#103. To save water and time, consider washing your face or brushing your teeth while in the shower.


#104. While staying in a hotel or even at home, consider reusing your towels.



#105. When backwashing your pool, consider using the water on your
landscaping.



#106. For hanging baskets, planters and pots, place ice cubes under the moss or dirt to give your plants a cool drink of water and help eliminate water overflow.



#107. Throw trimmings and peelings from fruits and vegetables into your yard compost to prevent from using the garbage disposal.



#108. When you have ice left in your cup from a take-out restaurant, don't throw it in the trash, dump it on a plant.



#109. Have your plumber re-route your gray water to trees and gardens rather than letting it run into the sewer line. Check with your city codes, and if it isn't allowed in your area, start a movement to get that changed.



#110. Keep a bucket in the shower to catch water as it warms up or runs. Use this water to flush toilets or water plants.



#111. When you are washing your hands, don't let the water run while you lather.

what does the ways that to conserve water off?




Trisha Lar


does it save money on your bills for water and local watersheds?
i really need help to find what is it for ways to that conserve the water off. please help me and thank you.



Answer
There are a number of ways to save water, and they all start with you.


When washing dishes by hand, don't let the water run while rinsing. Fill one sink with wash water and the other with rinse water.

Some refrigerators, air conditioners and ice-makers are cooled with wasted flows of water. Consider upgrading with air-cooled appliances for significant water savings.
#4
Adjust sprinklers so only your lawn is watered and not the house, sidewalk, or street.
#5
Run your clothes washer and dishwasher only when they are full. You can save up to 1,000 gallons a month.
#6
Choose shrubs and groundcovers instead of turf for hard-to-water areas such as steep slopes and isolated strips.
#7
Install covers on pools and spas and check for leaks around your pumps.
#8
Use the garbage disposal sparingly. Compost vegetable food waste instead and save gallons every time.
#9
Plant in the fall when conditions are cooler and rainfall is more plentiful.

Tip #10
For cold drinks keep a pitcher of water in the refrigerator instead of running the tap. This way, every drop goes down you and not the drain.

#11
Monitor your water bill for unusually high use. Your bill and water meter are tools that can help you discover leaks.
#12
Water your lawn and garden in the morning or evening when temperatures are cooler to minimize evaporation.
#13
Wash your fruits and vegetables in a pan of water instead of running water from the tap.
#14
Spreading a layer of organic mulch around plants retains moisture and saves water, time and money.
#15
Use a broom instead of a hose to clean your driveway and sidewalk and save water every time.
#16
If your shower fills a one-gallon bucket in less than 20 seconds, replace the showerhead with a water-efficient model.
#17
Collect the water you use for rinsing fruits and vegetables, then reuse it to water houseplants.
#18
If water runs off your lawn easily, split your watering time into shorter periods to allow for better absorption.
#19
We're more likely to notice leaks indoors, but don't forget to check outdoor faucets, sprinklers and hoses for leaks.
#20
If you have an automatic refilling device, check your pool periodically for leaks.
#21
Check the root zone of your lawn or garden for moisture before watering using a spade or trowel. If it's still moist two inches under the soil surface, you still have enough water.
#22
When buying new appliances, consider those that offer cycle and load size adjustments. They're more water and energy efficient.
#23
Shorten your shower by a minute or two and you'll save up to 150 gallons per month.
#24
Upgrade older toilets with water efficient models.
#25
Adjust your lawn mower to a higher setting. A taller lawn shades roots and holds soil moisture better than if it is closely clipped.
#26
When cleaning out fish tanks, give the nutrient-rich water to your plants.
#27
Use sprinklers for large areas of grass. Water small patches by hand to avoid waste.

Tip #28
Put food coloring in your toilet tank. If it seeps into the toilet bowl without flushing, you have a leak. Fixing it can save up to 1,000 gallons a month.

#29
When running a bath, plug the tub before turning the water on, then adjust the temperature as the tub fills up.
#30
Walkways and patios provide space that doesn't ever need to be watered. These useful "rooms" can also add value to your property.
#31
Collect water from your roof to water your garden.
#32
Designate one glass for your drinking water each day or refill a water bottle. This will cut down on the number of glasses to wash.
#33
Rather than following a set watering schedule, check for soil moisture two to three inches below the surface before watering.
#34
Install a rain sensor on your irrigation controller so your system won't run when it's raining.
#35
Don't use running water to thaw food. Defrost food in the refrigerator for water efficiency and food safety.

Tip #36
Use drip irrigation for shrubs and trees to apply water directly to the roots where it's needed.

#37
Grab a wrench and fix that leaky faucet. It's simple, inexpensive, and you can save 140 gallons a week.
#38
Reduce the amount of lawn in your yard by planting shrubs and ground covers appropriate to your site and region.
#39
When doing laundry, match the water level to the size of the load.
#40
Teach your children to turn off faucets tightly after each use.
#41
Remember to check your sprinkler system valves periodically for leaks and keep the sprinkler heads in good shape.

Tip #42
Use a water-efficient showerhead. They're inexpensive, easy to install, and can save you up to 750 gallons a month.




Powered by Yahoo! Answers