Jumat, 29 November 2013

Pool automatic chlorine feeder not feeding, can I fix it?

best automatic pool cleaner for small pool on ... 'Lil Shark Automatic Pool Cleaner For Aboveground Pools (GW8000
best automatic pool cleaner for small pool image



ajith t


I have DE filter pump
It has a 1&1/2 feet tall automatic chlorine feeder two years old. It is not feeding the chlorine tablets I put in it. It was working until few months before. It is on position. Water fills in it when the pump on but the chlorine tablets remain same level for ling time now. It is Pentair model 320
Why? Can I fix it?



Answer
Hi There,

the device works by flowing a controlled amount of water into the device, through the chlorine tablets then back into the pipe ( through the control valve) then to the pool.

You can probably fix the chlorinator yourself by shutting down the pump and letting the water drain out.

Next remove the chlorine tablets and look inside for a clogged screen or possibly the check valve is plugged.

Note:The device should fill with water when the pump is turned on through the check valve but the check valve should not let the water go back down when the pump is turned off.

It is very possible the chlorine control valve has small bits of tablets or dust, dirt , etc that is not letting the water flow normally through the tablets and out through the outlet tube.

I am sure that when you clean everything out, check the screen and control valve and make sure the check valve lets water in but not out you will solve the problem.

Hope this helps,
Al

What happens if pesticide gets in a swimming pool?




M W


A diluted amount of LAMBDA-CYHALOTHRIN got in my swimming pool. It is an over the counter pesticide to control ants, mosquitoes, beetles etc . A sudden wind gust drifted some of the pesticide in my swimming pool.


Answer
If it was a small amount and you are running a filter, it shouldn't be a problem. I would run the filter for at least 24 hours straight and brush the sides and bottom of the pool every few hours to stir up and remaining pesticide. If you have an automatic pool cleaner, you will also want to run it to help stir the water. You might also want to shock the pool.




Powered by Yahoo! Answers

how to clean my pool at home with only the cleaning tablets.?

automatic pool cleaner instructions on pool cleaner hayward navigator pro hayward axv552whp automatic pool ...
automatic pool cleaner instructions image



mom


i have a 12'x30" pool it holds 1,718 gallons of water.the pump filters 530 gallons of water per hour. the pool by morning is green and slimmy. the bottom of the pool is covered in green and brown crud?


Answer
Cleaning your pool is a must to ensure bather comfort and protect your equipment. How to clean your pool is simple, and we've asked pool professional John Kistler to fill us in on the whys of pool cleaning.
Instructions
Difficulty: Moderately Easy

Steps:

Step 1 Use a manual brush and pool vacuum on all areas of the walls and floor at least once a week, even if your pool is equipped with an automatic system, says John Kistler of Sunflower Pool & Spa in Salina, Kansas. There are some places in every pool that the automatic cleaning systems miss.

Step 2 Pay particular attention to corners, stairs and other hard-to-reach areas that get little circulation.

Step 3 Keep your pool maintained. A clean pool is also a function of a working filtration system and proper pH levels. Use a sanitizer to help fight bacteria, and shock the pool on a regular basis (see How to Shock a Pool) to help keep it clean and crystal-clear.

With the power behind kitchenaid mixer motors, why do you think they do not turn off when the head is tilted?




John


I just tried to remove an attachment from a Kitchen Aid mixer and, not realizing what button/knob to push to loosen the attachment, turned it on with my hand on it. It yanked my hand pretty good and luckily damage was not worse but the whole incident makes me question...

The motor inside the mixer is (and needs to be) very powerful. Why on earth hasn't Kitchen Maid added a safety switch to the tilt head so that the mixer cannot be powered when the head is tilted up? Is there some need to have the motor on with the head tilted? I've seen plenty of power tools with far less power which have far more safety designed into the product.
While I appreciate Tom's answer below, there are a few things I take issue with.

1. Virtually every engineer, executive, secretary or janitor working for Kitchen Aid knows the following:

a. Most owners of the mixer will NOT unplug the unit each and every time attachments are changed.

b. All members of a household in which a mixer is present will not have read the entire operating manual.

c. People often make mistakes for a large variety of reasons.

and....

2. Error-proofing the mixer such that the motor cannot run when attachments are being changes is entirely possible.

After working extensively with both American and Asian automakers, one of many cultural difference I've noticed is what Tom stated. The Asians do not look at error-proofing and think "it can't be done," they look at it and think "it can be done, and if it is already being done, it can be done better."

Anyway, I digress. From reading this I think the answers to my question
I also find it amusing that electric mixers are a top contender when I search for "most dangerous kitchen appliances." Maybe it simply is because engineers cannot and will not make them safer.



Answer
It's impossible to idiot proof everything. Why would you work on any power equipment with power still applied? Especially since the operating manual specifically says never to do that.
You have a large brain that should be sufficient to protect you from this sort of mishap.
You're essentially asking how to protect you from yourself. Can't be done.

It's not a defect... you ignored the instructions. It's like crawling under a car when all that's holding it up is the jack and you didn't place jack stands like you're supposed to. Ignore the common sense part and no one can or will protect you.

BTW, what power tool with far less power has more safety designed into it? Hand drills are very powerful but there is nothing to keep them from energizing while changing bits. Same with my drill press. Nothing to keep it from starting while I have a chuck key inserted.
Can't get any safer than disconnecting power... like you were instructed to.

Direct from Kitchenaid:
"When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. To protect against risk of electrical shock, do not put mixer in water or other
liquid.
3. Close supervision is necessary when any appliance is used near children.
4. Unplug from outlet when not in use, before putting on or taking off parts, and
before cleaning."

EDIT:
So what I am noticing is that you speak in generalities. You still haven't named that power tool with far more safety build into it, that you mentioned.
As far as pulling the Asian vs. American mentality card, that's a crock. Easy to say, but you can't support the statement other than with your own anecdotal statement. Nonetheless, this is NOT AN ENGINEERING problem or issue. An interlock would be easy. So would unplugging the machine before you monkey with it, but you didn't do that. The latter is less expensive and more practical.
Guess what would happen if there were an interlock and it failed? You'd be wanting to sue. I'm not so sure you're not intimating that already with this supposed "design defect".
Learn your lesson already... keep your finger out of the light socket. (there's no interlock there, either)

Your statements about what "most owners" will or will not do are also unfounded and unsubstantiated. You made that up, too.
If you can't/don't follow instructions then THAT'S YOUR FAULT. Period.

I'm sick and tired of this mentality. Space heaters burn down homes all the time. So do matches. Or is is people using space heaters and matches that burn things down?
A car can be put into forward gear and the throttle stepped on even if when there's a store front full of people in front of you. GASP! Why aren't engineers doing something about that?? Surely the Asians have noticed this looming danger and are all over it!

The MOST dangerous thing in your kitchen is YOU. The fact that you and most of your friends (not most people) choose to ignore instructions, warnings, and cautions actually gives me hope for humanity as some of those genes will soon be removed from the pool.

Maybe all applicances should also have GFI built INTO them in case some idiot who wants to make toast next to his hot tub plugs it into an extension cord that's not on a GFI circuit?
Maybe toasters should have automatic doors on them to keep people from sticking butter knives into them while they're plugged in?
You getting the point yet? Probably not.

The bottom line, that you don't like and won't accept, is that there is NO TREND of people being injured by their stand mixers. The mixers that are the most dangerous are the hand and wand mixers with high-speed exposed blades. (you failed to research that before you listed "electric mixers" as a dangerous kitchen appliance) Perhaps that's the part that amused you.

Get a grip and stop blaming everyone for not protecting you from yourself. It can't be done and should not be done.
You couldn't figure out which button to press so you fumbled with it plugged in. Not good.... and contrary to what you were told not to do.

Here's another: Don't drive on the left side of the road in the US. It's not safe. There is nothing to stop you from doing this, even though the car has a lot of power. Just don't do it.




Powered by Yahoo! Answers