automatic pool cleaner gets stuck image
Tony
The alkalinity in my in ground pool (25K gallons) is very high. It takes 20 drops in the tester to produce clear test. I've already bought a new tester. My ph is normal. How do I lower the alkalinity without also lowering the PH too much? I have to add acid but won't that also lower th PH too much?
Answer
You can lower the alkalinity with muriatic acid. 1.3 pints per 10,000 gallons will lower it by 10ppm. 3.25 pints in your pool will lower it by 10ppm. To get to the level you need of approximately 100-120 you will need to use 26 pints of muriatic acid to reduce it by 80ppm or 3.25 gallons of liquid muriatic acid.
You are testing the TA and getting 200ppm for your inground pool right? Make sure you walk a perimeter around the pool while pouring this in and wear proper safety equipment (eye protection and gloves) as muriatic acid is a diluted form of hydrochloric acid. Make sure you turn off any automatic chlorinators or remove chlorine pucks/sticks from the pool and NEVER let muriatic acid come into direct contact with chlorine products. Once in the water it will play safe but outside of water it will create chlorine gas which will kill a human in a matter of minutes.
You can get muriatic acid from the pool store or a local hardware store (sold as a cleaning agent).
You can lower the alkalinity with muriatic acid. 1.3 pints per 10,000 gallons will lower it by 10ppm. 3.25 pints in your pool will lower it by 10ppm. To get to the level you need of approximately 100-120 you will need to use 26 pints of muriatic acid to reduce it by 80ppm or 3.25 gallons of liquid muriatic acid.
You are testing the TA and getting 200ppm for your inground pool right? Make sure you walk a perimeter around the pool while pouring this in and wear proper safety equipment (eye protection and gloves) as muriatic acid is a diluted form of hydrochloric acid. Make sure you turn off any automatic chlorinators or remove chlorine pucks/sticks from the pool and NEVER let muriatic acid come into direct contact with chlorine products. Once in the water it will play safe but outside of water it will create chlorine gas which will kill a human in a matter of minutes.
You can get muriatic acid from the pool store or a local hardware store (sold as a cleaning agent).
What is the best automatic inground pool cleaner? What brand and price?
Francaise
Its a vinyl inground pool. Rectangular 18x36. Also budget is an issue, I am looking at spending $500 or less.
Answer
After 25 years of hearing how great floor head systems are, I have come to a conclusion. If your pool would have stayed looking nice with any cleaning system in your pool, it will stay nice with a floor head system.
If you plan on owning a pool for 5-6 years, or longer, in my opinion the best cleaning system(Dollar for Dollar) is a Polaris 280 with a booster pump and a separate time clock. The reasons are as follows:
1.)Low cost of repairs. I have clients with Polaris 180âs that are 25 years old. (The 280 has the same drive system.) Total repair costs in 25 years are less than $300.00 total (Not counting bag replacements.) I Personally, have owned a Polaris 280 for almost 5 years and have not spent a dime. (other than on 2 bags, and one of them was torn by my kids, and the other by a big pine cone. )
2.)It will clean most pools spotless in 10-20 minutes per day. You have seen our (5) 40â plus Ponderosa pines that overhang our pool area. Not counting steps and love seat, if we keep the bag cleaned, the floor stays spotless.
3.)Initial installation costs should be in the $1400.00-1600.00 range. Floor head systems are usually about double the initial expense. Also, the motor for the cleaning system is usually a 2 H.P. or larger, and the pool needs to run for substantially greater times to even get close to what a Polaris will do in ½ hour or less. Also, if you are not the initial purchaser of the system, you will not get a lifetime warrantee. Replacement gear systems, floor heads, ⦠can average more than $200.00 per year after the first 2 year, not to mention if the cleaner is not working correctly, i.e. heads jammed in the up position, actuator gears jammed, ⦠you are running that large motor with absolutely no cleaning going on. Any way you look at it, running a ¾ H.P. booster motor for 20-30 minutes is going to be a lot cheaper than running a 2 H.P. for 3-4 hours. Add into this that most motors run for more than 2 hours per day seem to have a life span in the 5-6 year range, and that a 2 H.P. motor is about double the cost, I cannot see spending the money.
4.)Suction side cleaners have a lower initial cost, but are annoying because either they will not pick up sticks, twigs, small rocks, ⦠or they will, and then they will completely stop working until you spend 10 minutes pulling them out and cleaning the debris out of them. Some of these will end up needing replacement parts just because of punctured diaphragms, ⦠This is in addition to an average annual repair cost of about $200-250, after the first year or two. In less than 5 years(More likely 3 years), if you add in electricity savings, pool cleanliness and thus chemical costs savings, and electrical savings, you have more than paid for the Polaris. If you add to this the fact that, if you have a suction side cleaner, you will have had to bring it in to the shop at least 4-5 times, having a non-functional cleaning system, thus a horridly dirty pool at least 4-5 times, the fact that often it dies a slow death each time so your pool doesnât look right for months prior to each rebuilding, and the repeated hassles of needing to unplug the system when ever any ârealâ debris ends up in the pool, and I wonât have anything else in my pool, or my families pools. To summarize, If you are buying a cleaner and are selling the home quickly, I would probably go with a pool Vac(if there are no rocks, sticks, big leaves, ⦠In other words, dirt only, but your annual repair costs will be high) or a Kreepy Krauley if you have anything else(Or want 40% less repair costs than the Pool Vac).
5.)Floor heads, or suction cleaners destroy the natural water flow around the pool which is responsible for moving the debris around to the skimmer on the surface, and for moving silt, and dirt to the main drain. Therefore, the surface areas of both sides of the pool(If the cleaners are functioning properly) will be an average of 20-40% dirtier than the same pool with a pool vac, return lines properly adjusted, and approximately ¾ of the suction of the pool going to the main drain. Also, since almost all of the suction for a suction side cleaner is directed to the cleaner, and thatâs run through an extra 30 feet or so of corrugated hose, the water flow is greatly reduced, and to get the same water filtration you will need to run that system approximately 25% -30% longer than a system without a suction cleaner. Thatâs 1 ¾ hrs longer running a 1 H.P. motor than is needed to run the ¾ H.P booster. Also, as a suction cleaner picks up debris, assuming it doesnât get plugged up and stop functioning all together, the baskets will fill up and all the suction to the pool will decrease or stop. There are times during the year where about 60% of the repair work I do is related to suction cleaning systems picking up too much debris. Note: This is never covered under any warrantee.
There is more that I could add, but I am too tired to do so now. Installation is as follows:
After 25 years of hearing how great floor head systems are, I have come to a conclusion. If your pool would have stayed looking nice with any cleaning system in your pool, it will stay nice with a floor head system.
If you plan on owning a pool for 5-6 years, or longer, in my opinion the best cleaning system(Dollar for Dollar) is a Polaris 280 with a booster pump and a separate time clock. The reasons are as follows:
1.)Low cost of repairs. I have clients with Polaris 180âs that are 25 years old. (The 280 has the same drive system.) Total repair costs in 25 years are less than $300.00 total (Not counting bag replacements.) I Personally, have owned a Polaris 280 for almost 5 years and have not spent a dime. (other than on 2 bags, and one of them was torn by my kids, and the other by a big pine cone. )
2.)It will clean most pools spotless in 10-20 minutes per day. You have seen our (5) 40â plus Ponderosa pines that overhang our pool area. Not counting steps and love seat, if we keep the bag cleaned, the floor stays spotless.
3.)Initial installation costs should be in the $1400.00-1600.00 range. Floor head systems are usually about double the initial expense. Also, the motor for the cleaning system is usually a 2 H.P. or larger, and the pool needs to run for substantially greater times to even get close to what a Polaris will do in ½ hour or less. Also, if you are not the initial purchaser of the system, you will not get a lifetime warrantee. Replacement gear systems, floor heads, ⦠can average more than $200.00 per year after the first 2 year, not to mention if the cleaner is not working correctly, i.e. heads jammed in the up position, actuator gears jammed, ⦠you are running that large motor with absolutely no cleaning going on. Any way you look at it, running a ¾ H.P. booster motor for 20-30 minutes is going to be a lot cheaper than running a 2 H.P. for 3-4 hours. Add into this that most motors run for more than 2 hours per day seem to have a life span in the 5-6 year range, and that a 2 H.P. motor is about double the cost, I cannot see spending the money.
4.)Suction side cleaners have a lower initial cost, but are annoying because either they will not pick up sticks, twigs, small rocks, ⦠or they will, and then they will completely stop working until you spend 10 minutes pulling them out and cleaning the debris out of them. Some of these will end up needing replacement parts just because of punctured diaphragms, ⦠This is in addition to an average annual repair cost of about $200-250, after the first year or two. In less than 5 years(More likely 3 years), if you add in electricity savings, pool cleanliness and thus chemical costs savings, and electrical savings, you have more than paid for the Polaris. If you add to this the fact that, if you have a suction side cleaner, you will have had to bring it in to the shop at least 4-5 times, having a non-functional cleaning system, thus a horridly dirty pool at least 4-5 times, the fact that often it dies a slow death each time so your pool doesnât look right for months prior to each rebuilding, and the repeated hassles of needing to unplug the system when ever any ârealâ debris ends up in the pool, and I wonât have anything else in my pool, or my families pools. To summarize, If you are buying a cleaner and are selling the home quickly, I would probably go with a pool Vac(if there are no rocks, sticks, big leaves, ⦠In other words, dirt only, but your annual repair costs will be high) or a Kreepy Krauley if you have anything else(Or want 40% less repair costs than the Pool Vac).
5.)Floor heads, or suction cleaners destroy the natural water flow around the pool which is responsible for moving the debris around to the skimmer on the surface, and for moving silt, and dirt to the main drain. Therefore, the surface areas of both sides of the pool(If the cleaners are functioning properly) will be an average of 20-40% dirtier than the same pool with a pool vac, return lines properly adjusted, and approximately ¾ of the suction of the pool going to the main drain. Also, since almost all of the suction for a suction side cleaner is directed to the cleaner, and thatâs run through an extra 30 feet or so of corrugated hose, the water flow is greatly reduced, and to get the same water filtration you will need to run that system approximately 25% -30% longer than a system without a suction cleaner. Thatâs 1 ¾ hrs longer running a 1 H.P. motor than is needed to run the ¾ H.P booster. Also, as a suction cleaner picks up debris, assuming it doesnât get plugged up and stop functioning all together, the baskets will fill up and all the suction to the pool will decrease or stop. There are times during the year where about 60% of the repair work I do is related to suction cleaning systems picking up too much debris. Note: This is never covered under any warrantee.
There is more that I could add, but I am too tired to do so now. Installation is as follows:
Powered by Yahoo! Answers
best automatic pool skimmer
BalasHapusbest above ground pool skimmer
floating skimmer for above ground pool
above ground pool skimmers
pool skimmers above ground